Fundamentals of Engineering exam, also known as the Engineer in Training exam, and earlier in some states as the internal examination of Engineering, is the first of two exams that engineers must pass in order to obtain a license as professional engineer in the USA. The exam is open widely to anyone with a degree in engineering or a related field, or currently enrolled in the final year of a degree program accredited by ABET engineering. Some tips allow state undergraduate students take before his senior year, and many states allow those who have never attended an approved to take the exam if they have a certain number of years been working experience in engineering . A selection of special states with ABET accredited by the “engineering technology” or degrees “TAC” to take the exam. The state of Michigan has admission prerequisites for the FE. The test is administered by the National Council of Examiners for Engineering and Surveying.


The exam is eight hours in total, divided into two sessions of four hours with a lunch break 60 minutes in between. This explains the time required to collect the test in the morning. General admission starts tomorrow at 7:15 AM Failure to appear before the doors are closed will result in the student being away from the test site. Normally it takes 20 minutes for prosecutors to hand out materials and revise examination procedures, so the morning session begins at 8:00 AM Similar procedures are followed in the afternoon session, with input from around 13:15 and ending around 1:30 pm, the test itself begins 1: 30-13: 45.

The morning session is an overview of 120-question for which all examinees should sit, while the afternoon session consists of 60 questions and is more oriented discipline. For the second half, the examinees choose one of the following seven events: chemical engineering, civil engineering, environmental engineering, electrical engineering, mechanical engineering, industrial engineering, or other disciplines. Before April 2010, the other test subjects is called the general test, but was renamed to reflect better to take it. From October 2010 examination, choosing the afternoon examination is required to be made to the register. Before this, the beginning of the afternoon session, the examinees were given a booklet containing the seven tests and could then decide which one to take.

Topics covered in the overall review are discussed in courses taken by students in engineering, and include:
Engineering Probability and Statistics
Ethics and Business Practices
Economics Engineering
Mechanical Engineering
Strength of Materials
Properties of Materials
Fluid Mechanics
Electricity and Magnetism

Examinees receive results about two months after the test date. Those who pass the test are designated engineer in training or an equivalent designation given as a practical engineer, licensed by your state board for engineers, and is to some extent through the certification process. After completing an apprenticeship, an EIT can qualify to take the examination of professional engineer. Certification is awarded upon successful completion of the PE exam. Timekeeping apprenticeship under a professional engineer is 4 years of work experience for graduates of an engineering program accredited by ABET.
Several changes in the format of the examination will be held in January 2014, including the transition to a computerized test six hours.

Take the test
Tools and scrap paper Scripture can not be brought to the test site. Mechanical pencils are issued to all examinees and the test booklet can be used as scrap paper to work problems. No calculators are permitted except those specifically approved by NCEES listed below, these models have no programming or capabilities that would allow people to cheat. The only reference material that can be used is a manual that is given to those examined in the morning, but should be left in the room after each session. For purposes of the study, this manual can be obtained by downloading from the NCEES website or by purchasing a printed copy. However, examinees cannot bring their own copies of the test site, but use those issued to them by prosecutors and cannot write to them.

Policy calculator
NCEES only allows the following calculators for use in the fundamentals of engineering exam:
Casio FX-115
Hewlett-Packard: HP 33s and 35s
Texas Instruments: TI-30X and TI-36X

The calculator must clearly show your model number for the exam proctors calculator can quickly identify and approve for use during the exam. The list of calculators allowed each November is reviewed. It is crucial that any student see the NCEES website to verify calculator is acceptable. Absolutely other calculators are not allowed. Using an illegal after the test has begun calculator will lead to the examinee taking your examination will be immediately withdrawn and examination will not be scored.

US Patent Office
Previously, the approval of the Fundamentals of Engineering exam along with graduation with any degree or equivalent experience, satisfied US Patent and technical requirements of the Trademark Office for sitting by your registration exam to become either a lawyer of patents or patent agent. However, it is no longer necessary step FE exam. The typical way is to meet the technical requirements for possession of a bachelor’s degree in a specific or accumulate a certain number of hours of college credit in a designated technical area technical area.

Tagged on:

Leave a Reply

Your email address will not be published. Required fields are marked *